Dell PERC S110 Controller
Device Driver for Windows Server 2016

Version:  3.2.0.0014


TABLE OF CONTENTS
================

1.0    Introduction
2.0    Compatibility / Minimum Requirements
3.0    Install Instructions
         3.1  Installing the Driver During Operating System Installation
		 3.2  Installing  driver for "Dell PERC S110  Configuration Device" after installing Operating System.
         3.3  Updating an Existing Windows Driver
         3.4  Driver Update using Dell Update Package (DUP)
4.0   Fixes or Enhancements in this Release
5.0   Additional Information
6.0   Known Issues


1.0 Introduction
================

This is the driver for following PowerEdge Expandable RAID Controller:

    PERC S110 SWRAID
    

2.0  Compatibility / Minimum Requirements
=================================

This device driver requires the following minimum Operating System version:

Windows Server 2016
NOTE: Dell recommends the latest Service Pack available for your Operating System


3.0 Install Instructions
========================

This driver package contains the Windows device driver 
for PERC S110 controller.

To build the installation media these files should be 
copied to a USB key.


3.1 Installing the Driver during Operating System Installation
-------------------------------------------------------------------------

1. Power on the system and boot to the Microsoft Windows Server CD.

2. Follow the screen instructions until you reach the 
                "Where do you want to install Windows?" section.

3. Insert the CD-ROM, DVD, or USB flash drive that
   contains the driver files.

4. At the Load Driver sub-screen, click Browse.
   Select the directory that has the controller driver files. Click OK.

5. At the Select the driver to be installed window, select Dell PERC appropriate Controller driver... Click Next to load the driver files.

6. After the driver loads you will return to the "Where do you want to 
   install Windows?" screen (partitions can be configured on this screen), 
   press "Next" again to continue the installation process as usual.

7. Once the installation is completed, install the configuration driver if required, used by Dell Open Manage(OMSA) component to configure the S110 controller. 

3.2 Installing  driver for "Dell PERC S110  Configuration Device" after installing Operating System.
--------------------------------------------------------------------------------------------------
NOTE: It is important that you idle your system before you update the driver.

1. Insert the CD-ROM, DVD, or USB flash drive, that contains the driver files.
2. Open the directory that contain driver files. Right click the bccfg3.inf and select Install option.
3. You will get pop-up with message  "The operation completed successfully".  Click ok.


3.3 Updating an Existing Windows Driver
-------------------------------------------------

Perform the following steps to update the Windows driver for the RAID controller and S110 Configuration device, already installed on your system.

NOTE: It is important that you idle your system before you update the driver.

1. Press "Start" > "Control Panel" > "System and Security" > "System".
   The "View basic information about your computer" screen displays.
2. Click on the "Device Manger" link on the left.
   The "Device Manger" window opens
4. Click "Storage controller" for updating "Dell PERC S110  Controller" and "System devices" for updating "Dell PERC S110  Configuration Device"
5. Double-click the device for which the driver has to be updated.
   The following steps(from Step 6 through 11 ) have to be performed for both the
   a) Dell PERC S110  Controller
   b) Dell PERC S110  Configuration Device
6. Click the "Driver" tab and click on "Update Driver..." button.
   The screen for the Upgrade Device Driver Wizard displays.
7. Insert the appropriate media (driver diskette/USB key/CD/DVD).
8. Click "Browse my computer for driver software"
9. Click "Let me pick from a list of device drivers on my computer"
10.Click the "Have Disk" button and browse to the appropriate location.
11.Select the RAID controller and click "Next"
12.The new driver will be uploaded, close all windows and restart your 
   computer for the changes to take effect.


3.4  Driver Update using Dell Update Package (DUP)
---------------------------------------------------------------

A Dell Update Package (DUP) is a self-contained executable in a standard 
Dell package format and each Update Package is designed to update a single 
component on your system. 

    DUP Download 
    ------------------

1. Click the Download Now link to download the file. 
2. When the File Download window appears, click Save to save the file to 
   your hard drive. 

    Driver Update 
    -----------------

1. Browse to the location where you downloaded the file and double-click 
   the new file. 
2. Read over the release information presented in the dialog window. 
3. Download and install any prerequisites identified in the dialog window 
   before proceeding. 
4. Click the Install button. 
5. Follow the remaining prompts to perform the update.

   Silent Driver Update
   ------------------------

Execute the DUP from the command line (or script) as follow

                DRVR_WIN_Rxxxxxx.exe s l=filename r

   Where s  Executes the update silently without user intervention.
          r  Reboots the system, if required, after performing the update.
          l=filename  Appends logged messages to a specified ASCII file; 
                         creates a new file if one does not exist.

For more command line options type

                DRVR_WIN_Rxxxxxx.exe 

or consult the Dell Update Package User's Guide.



4.0 Fixes or Enhancements in this Release 
=========================================

      




5.0 Additional Information
==========================



6.0 Known Issues
================